MAXDATA QutePC?1000 Guida Utente Pagina 106
- Pagina / 163
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
106 Configuration Software and Utilities
107MAXDATA PLATINUM 90002R Server System
Console Redirection
The BIOS supports redirection of video output and keyboard input via serial link. This section details
the serial redirection scheme. For redirection over LAN (Serial over LAN or SOL), see the ISM online
help.
When console redirection is enabled, local (host server) keyboard input and video output are passed
both to the local keyboard and video connections, and to the remote console via the serial link. Keyboard
inputs from both sources are considered valid and video is displayed to both outputs.
With console redirection, you can operate the server system without having a keyboard or monitor
attached to it. Setup and any other text-based utilities can be accessed via console redirection. Note
that serial redirection uses PC-ANSI and the UART settings assume 1 stop bit.
Operation
NOTE
When console redirection is enabled, the text on the local console screen will draw slowly when it is
operating under EFI. This is especially true when a low baud-rate modem is used, such as the default
baud rate of 19.2K. This is because EFI is not an interrupt-driven environment and it uses a polling
mechanism to communicate with the remote console.
When redirecting through a modem, as opposed to a null modem cable, the modem needs to be
congured as follows:
• Auto-answer (for example, ATS0=2, to answer after two rings).
• Modem reaction to DTR set to return to command state (such as AT&D1). Failure to provide
the modem reaction results in the modem either dropping the link when the server reboots (as
in AT&D0) or becoming unresponsive to server baud rate changes (as in AT&D2).
• The Setup/EMP option for handshaking must be set to CTS/RTS + CD for optimum
performance. The CD refers to carrier detect. If the EMP is sharing the COM port with
serial redirection, the handshaking must be set to CTS/RTS+ CD. In selecting this form of
handshaking, the server is prevented from sending video updates to a modem that is not
connected to a remote modem. If this is not selected, video update data being sent to the
modem inhibits many modems from answering an incoming call. An EMP option utilizing CD
should not be used if a modem is not used and the CD is not connected.
Once console redirection is selected via Setup, redirection binary is loaded into memory and
activated during POST. While redirection cannot be removed without rebooting, it can be
inhibited and restarted.
Inhibiting and restarting is accomplished through an INT 16h mechanism. The standard INT 16h
(keyboard handler) function ah=05h places a keystroke in the key buffer, as if an actual key is
pressed. Keystrokes buffered this way are examined by redirection; if a valid command string
has been sent, it is executed. The following commands are supported:
• Esc-CDZ0 - Inhibit Console Redirection. In order to inhibit redirection, the software must call
INT 16h, function ah=05h ve times to place the ve keys in the key buffer. Keystrokes sent
to the INT 16h buffers to invoking a command are buffered, and should be removed through
normal INT 16h calls to prevent these keystrokes from being passed to another application.
When redirection is inhibited, the serial port is released and can be used by other applications.
• Esc-CDZ1 - Restart Console Redirection. Restarting reclaims the serial port and continues
redirection
- Product Guide 1
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 4 Technical Reference 125 8
- Safety Warnings 153 8
- 8 Contents 9
- Important Safety Information 11
- Conventions 12
- 1 System Description 13
- External Chassis Features 15
- Front Panel 16
- Peripheral Bay 17
- Hot-swap Hard Drive Carrier 18
- Removable Media Drive Bay 19
- CAUTION 19
- Power Supply Bay 20
- • AC input #1 available 21
- • AC input #2 available 21
- • TS-OK signal is asserted 21
- Chassis Rear 22
- Internal Chassis Features 23
- Cooling Subsystem 25
- CAUTIONS 25
- 26 System Description 26
- NOTES 27
- Processor Power Pods 28
- 2 Board Set Description 29
- 30 Board Set Description 30
- Main Board 31
- Processor Sockets 33
- Memory Subsystem 33
- SCSI Controller 34
- Network Interface Controller 34
- Video Controller 34
- IDE Controller 35
- PCI Riser Board 36
- SCSI Backplane Board 37
- Front Panel Board 39
- Size] 46
- CMOS Clear 47
- WARNING 47
- BIOS Recovery Mode 48
- BIOS Setup 49
- Setup Screens 50
- Advanced 51
- Security 52
- System Management 52
- LSI Logic SCSI Utility 55
- System Maintenance Utility 57
- Remote Keyboard Navigation 58
- Local Keyboard Navigation 58
- About Box Information 59
- Server Discovery 60
- Remote SMU Application 60
- Running from CD 62
- Local SMU Application 62
- Shutdown SMU Application 63
- Access Mode 65
- Privilege Level Limit 65
- Enable DHCP 65
- LAN Alert Conguration 67
- Enable LAN Alerting 67
- SNMP Community String 67
- Alert Settings 68
- New, Edit, and Delete Buttons 68
- New/Edit LAN Alert 68
- User Conguration Sub-task 71
- Enable User 72
- Enter Username 72
- Clear Password 72
- Enter/Verify New Password 72
- Edit Event Filter Settings 75
- Enable Event Filter 75
- Enable Alerts 76
- Congure Policies Button 76
- Alert Policy Table 76
- Edit Alert Policy Entry 78
- Enable Policy Entry 78
- Policy Number 78
- Policy Type 78
- Select the Destination 79
- Connection Mode 80
- Modem Mode Conguration 81
- Modem Init String 81
- Modem Escape Sequence 82
- Hang-up Sequence 82
- Dial Command 82
- Ring Duration 82
- Ring Dead Time 82
- Destination Dial Strings 83
- New/Edit Dial String 84
- Destination Dial String 84
- Page Destination Conguration 85
- Enable Paging 85
- Data Bits 87
- Call Retries 87
- Terminal Mode Conguration 87
- Enable Terminal Mode 87
- Power Conguration Sub-task 89
- SEL Viewer 90
- Viewing Events in the SEL 91
- Save Log Button 93
- Open Log Button 93
- Clear SEL Button 93
- Properties Button 93
- Reload Button 93
- Display as Hex Button 94
- Display as Text Button 94
- SDR Viewer 94
- Viewing SDRs 95
- Viewing FRUs 97
- Save To File Button 98
- Open File Button 98
- ISM Front-end Help 100
- SMU Table of Contents Help 100
- EFI Platform Diagnostic Tests 102
- EFI Service Partition 104
- Installing the Files 105
- Console Redirection 106
- Keystroke Mappings 107
- (xxh) = ASCII character xx 108
- NS = not supported 108
- NS = Not supported 108
- Limitations 109
- Server Management Interface 109
- Server Conguration 109
- Terminal Mode 110
- Hardware Setup 111
- Serial Channel Conguration 111
- Console Conguration 113
- User Conguration 113
- Security Information 113
- Hex-ASCII Command Format 115
- Text Command Format 115
- Examples 115
- Shutting Down the Server 123
- 4 Technical Reference 125
- System Interconnection 126
- User-Accessible Interconnects 127
- Video Port 128
- Ethernet Connector 129
- Ultra320 SCA-2 HDD Connector 131
- Jumper Information 133
- Conguring Main Board Jumpers 134
- POST Error Codes and Messages 135
- Specic POST Code Modules 138
- SAL-A Module 138
- SAL-B Module 140
- SAL-F Module 143
- IA-32 Module 144
- Recovery Port 80 Codes 148
- POST Beep Codes 150
- Memory Test Failure 151
- Safety Warnings 153
- WARNING: English (US) 154
- AVERTISSEMENT: Français 156
- WARNUNG: Deutsch 158
- AVVERTENZA: Italiano 160
- ADVERTENCIAS: Español 162
Prodotti e manuali riguardandi Server MAXDATA QutePC?1000
Server MAXDATA PLATINUM 520 Manuale Utente
(31 pagine)
(31 pagine)
Server MAXDATA PLATINUM 110 Manuale Utente
(31 pagine)
(31 pagine)
Server MAXDATA PLATINUM 510 Manuale Utente
(6 pagine)
(6 pagine)
Server MAXDATA PLATINUM 400IR M6 Manuale Utente
(23 pagine)
(23 pagine)
Server MAXDATA PLATINUM 100 I M7 Manuale Utente
(23 pagine)
(23 pagine)
Server MAXDATA PLATINUM 200 I M7 Manuale Utente
(50 pagine)
(50 pagine)
Server MAXDATA PLATINUM 220 Manuale Utente
(31 pagine)
(31 pagine)
Server MAXDATA PLATINUM 3200 I M6 Manuale Utente
(59 pagine)
(59 pagine)
Server MAXDATA PLATINUM 100 I Manuale Utente
(29 pagine)
(29 pagine)
Server MAXDATA PLATINUM 510 Manuale Utente
(52 pagine)
(52 pagine)
Server MAXDATA PLATINUM 300 IR M6 Manuale Utente
(23 pagine)
(23 pagine)
Server MAXDATA PLATINUM 3200 I M6 Manuale Utente
(52 pagine)
(52 pagine)
Server MAXDATA PLATINUM 500 I M5 Manuale Utente
(31 pagine)
(31 pagine)
Server MAXDATA PLATINUM 5220 Manuale Utente
(6 pagine)
(6 pagine)
Server MAXDATA SR1202 M1 Guida Utente
(152 pagine)
(152 pagine)
Brunton Handbücher
Die Liste der Brunton Geräte enthält 20 Benutzerhandbücher und Anleitungen für 18 Modelle in 14 Gerätetypen
Commenti su questo manuale